02:06

Check and adjust tyre pressure by use of air or hydrogen | NIMI | DIGITAL | PUNJABI |

03:31

Assemble and inflate tyre to correct pressure | NIMI | DIGITAL | PUNJABI |

05:45

Measure the resistance using the voltage drop method | NIMI | DIGITAL | PUNJABI |

06:32

Measure current, voltage & analyze effects of short, open in parallel circuit| NIMI |DIGITAL|PUNJABI

06:12

Square butt joint on aluminum sheet (3mm.thick) in Flat position by OAW | NIMI | DIGITAL | PUNJABI |

10:59

Square butt,Lap and Tee joints on M.S Sheet 1.6 mm thick by brazing| NIMI | DIGITAL | PUNJABI |

10:02

Inspect soldered Joint, Detect the Defects and Test the PCB for Rework | NIMI | DIGITAL | PUNJABI |

06:25

Install and test the SMPS in PC | NIMI | DIGITAL | PUNJABI |

11:02

Practicing darning and patching | NIMI | DIGITAL | PUNJABI |

10:43

Stitching of ladies suit - PART 1 | NIMI | DIGITAL | PUNJABI |

03:52

Fitting of male and female thread components(Metric) | NIMI | DIGITAL | PUNJABI |

07:13

Make hexagonal bolt and nut (metric) and assemble | NIMI | DIGITAL | PUNJABI |

12:03

Measure current, voltage & analyze effects of short, open in series circuit|NIMI |DIGITAL |PUNJABI |

08:02

Measure voltage & current against individual resistances in circuit | NIMI | DIGITAL | PUNJABI |

08:17

Lap and Tee joint on M.S (2mm thick Sheet) in Horizontal position by OAW| NIMI | DIGITAL | PUNJABI |

07:29

Lap and Tee joint on M.S (2mm thick sheet) in Vertical position by OAW | NIMI | DIGITAL | PUNJABI |

06:20

Various trouble shooting in suspension system | NIMI | DIGITAL | PUNJABI |

15:00

Making snap gauge | NIMI | DIGITAL | PUNJABI |

10:55

Perform drilling using V- block & clamp | NIMI | DIGITAL | PUNJABI |

12:11

Superfluous hair and its removal methods | NIMI | DIGITAL | PUNJABI |

10:43

Demonstration of threading and tweezing | NIMI | DIGITAL | PUNJABI |

07:37

Screw thread (INTERNAL) metric & threading tool grinding | NIMI | DIGITAL | PUNJABI |

06:09

Prepare simple digital & electronic circuits using the software PART - 2| NIMI | DIGITAL | PUNJABI |

06:14

Square Butt joint on M.S. (2mm thick sheet) in Horizontal position by OAW | NIMI|DIGITAL|PUNJABI |

09:03

Tee joint on M.S Sheet ( 2mm thick Sheet) in Flat position by OAW| NIMI | DIGITAL | PUNJABI |

09:49

Prepare simple digital & electronic circuits using the software PART - 1| NIMI | DIGITAL | PUNJABI |

07:44

Construct and test bidirectional shift register PART -2 | NIMI | DIGITAL | PUNJABI |

07:41

Screw thread cutting (EXTERNAL) metric thread - tool grinding | NIMI | DIGITAL | PUNJABI |

04:45

Grinding of V tools for threading of 60 - degree & check with gauge | NIMI | DIGITAL | PUNJABI |

07:43

Lap joint on M.S Sheet 2 mm thick sheet in flat position by OAW | NIMI | DIGITAL | PUNJABI |

08:02

Square butt joints on M.S Sheet 2mm.thick Sheet Flat position using OAW| NIMI | DIGITAL | PUNJABI |

08:04

Construct and test bidirectional shift register PART - 1 | NIMI | DIGITAL | PUNJABI |

09:16

Display the two digit count value on 7 segment display using decoder -2 | NIMI | DIGITAL | PUNJABI |

04:10

Prepare Stud with Nut (Standard Size) Part - B | NIMI | DIGITAL | PUNJABI |

07:39

Prepare Stud with Nut (Standard Size) Part - A | NIMI | DIGITAL | PUNJABI |

07:30

Measuring, checking and recording in control chart | NIMI | DIGITAL | PUNJABI |

06:59

Visual inspection for visual defects e.g. dents, surface finish | NIMI | DIGITAL | PUNJABI |

08:27

Test for leakage and functionality of valves | NIMI | DIGITAL | PUNJABI |

04:16

Fitting of male and female threaded components ( BSW) | NIMI | DIGITAL | PUNJABI |

05:13

Screw thread cutting (BSW) internal RH &LH | NIMI | DIGITAL | PUNJABI |

06:38

Fillet -Tee joints on M.S.Plate (10mm thick plate) overhead position SMAW| NIMI | DIGITAL |PUNJABI |

08:15

Corner joints on M.S. Plate (10mm thick plate) in Overhead position SMAW| NIMI | DIGITAL | PUNJABI |

10:15

Construct and test an UP/Down Synchronous Decade counter IC using 74LS190| NIMI | DIGITAL |PUNJABI|

09:10

Display the Two digit count value on seven segment Display using Decoder| NIMI | DIGITAL | PUNJABI |

10:15

To make corner makings - self turned | NIMI | DIGITAL | PUNJABI |

11:32

Practice of fixing fasteners | NIMI | DIGITAL | PUNJABI |

03:45

Screw thread cutting external Including angular approach method Part -1| NIMI | DIGITAL | PUNJABI |

06:37

Screw thread cutting external Including angular approach method part-2 | NIMI | DIGITAL | PUNJABI |

09:26

Facial using ultrasonic device | NIMI | DIGITAL | PUNJABI |

11:05

Facial using galvanic device | NIMI | DIGITAL | PUNJABI |

10:00

Identify various types of capacitors, charging - discharging & testing | NIMI | DIGITAL | PUNJABI |

08:29

Locate accurate holes and make accurate hole for stud fit| NIMI | DIGITAL | PUNJABI |

15:22

Group capacitors for required capacity and voltage rating | NIMI | DIGITAL | PUNJABI |

08:22

File and fit straight and angular surfaces internally | NIMI | DIGITAL | PUNJABI |

06:21

Measure the resonance frequency in AC series circuits | NIMI | DIGITAL | PUNJABI |

07:18

Setting up Arc welding machines & accessories and striking an arc SWAW | NIMI | DIGITAL | PUNJABI |

05:43

Deposit straight line bead on MS plate in flat position using OAW | NIMI | DIGITAL | PUNJABI |

07:16

Depositing bead with filler rod on mild steel M.S.Sheet 2mm flat position | NIMI |DIGITAL |PUNJABI |

10:51

Facial using brushing unit device | NIMI | DIGITAL | PUNJABI |

10:26

Facial using high frequency device | NIMI | DIGITAL | PUNJABI |